Description
Masters Golf Clubmaker 30/60 club service
The Masters Golf Clubmaker 30/60 is a professional-grade, super-strong two-part epoxy adhesive supplied in a convenient dual-chamber syringe. Designed specifically for golf club assembly and repair, it delivers a reliable, long-lasting bond between shaft and clubhead for both steel and graphite shafts. With a generous working window and a fast cure to full playing strength, it is equally at home on a busy club repair bench or in the hands of a dedicated DIY clubmaker.
Key Features
- Super-Strong Formula: Extra-strength two-part epoxy engineered to withstand repeated high-speed impact forces during play.
- 30-Minute Working Time: Ample open time for mixing, applying and aligning a full set of clubs before the adhesive begins to set.
- Sets to Playing Strength in ~1 Hour: Cures to full bond strength in approximately one hour (conditions dependent), minimising workshop downtime.
- Cures Black: Finished cure colour is black, providing a clean, discreet appearance inside the hosel.
- Dual-Chamber Syringe: Pre-measured 1:1 resin-to-hardener ratio dispenses both components simultaneously for a consistently correct mix every time.
- Package Contents — 4 cl (40 ml): Sufficient quantity to complete a full set of club assemblies in a single session.
- Versatile Compatibility: Suitable for steel and graphite shafts bonded into metalwood, iron and putter hosels.
Technology in Detail
Super-Strong Two-Part Epoxy
The Clubmaker 30/60 uses a professional two-part formulation — resin and hardener — that, once combined, forms an exceptionally high-strength thermoset polymer bond. The cured adhesive is engineered to resist the repeated shear and tensile stresses generated during a full golf swing, ensuring the shaft-to-clubhead joint remains secure over thousands of shots. Its impact-resistant properties make it the preferred choice of professional clubmakers and repair workshops.
30-Minute Working Time
Unlike fast-cure epoxies that set within minutes, the 30/60 formula gives you a full 30-minute open working window from the moment mixing begins. This is ideal when assembling a complete set of clubs, as it allows you to methodically apply adhesive, seat each shaft in its hosel, and make precise alignment adjustments without the pressure of a rapidly closing working time. Air temperature and humidity will affect the exact open time — cooler conditions may extend it slightly.
~1-Hour Full Cure to Playing Strength
Once applied and the shaft seated, the Clubmaker 30/60 reaches full playing strength in approximately one hour under normal workshop conditions. This rapid cure cycle means a freshly shafted club can leave the bench the same day it was assembled, significantly reducing turnaround time compared to long-cure alternatives. Note that actual cure time may vary depending on ambient temperature — warmer environments accelerate curing, while colder conditions may require a little longer.
Black Cure Finish
The Clubmaker 30/60 cures to a clean black colour, which integrates neatly with the dark interior of most metal hosels and the finish of most modern shafts. Any small amount of squeeze-out at the hosel mouth remains inconspicuous once wiped clean, providing a professional, factory-quality appearance. The black finish also makes it straightforward to identify fully cured adhesive visually during inspection.
Dual-Chamber Syringe — Precision 1:1 Dispensing
The clever dual-chamber syringe format holds resin and hardener in separate chambers and dispenses both components simultaneously in the correct 1:1 ratio with a single squeeze. This eliminates the common measuring errors that can weaken the final bond when using separate bottles, and greatly speeds up the application process. The syringe format also keeps unused adhesive well-sealed and extends shelf life between uses.
Full-Set Assembly Capacity — 4 cl (40 ml)
Each syringe contains 40 ml (4 cl) of adhesive — sufficient to complete the shafting of a full set of clubs in one session. This makes the Clubmaker 30/60 a cost-effective choice for professional club fitters and repair technicians who need to work efficiently through multiple assemblies without interruption. The syringe tip allows precise application directly into the hosel, minimising waste.
Specifications
| Specification | Detail |
|---|---|
| Product Code | TL141 |
| Type | Two-part shafting epoxy — dual-chamber syringe |
| Working Time | 25–30 minutes |
| Cure Time (to playing strength) | ~60 minutes (conditions dependent) |
| Cure Colour | Black |
| Package Contents | 4 cl (40 ml) syringe |
| Compatibility | Steel and graphite shafts; all hosel types |
| Mix Ratio | 1:1 (resin : hardener) |
| Brand | Masters Golf |
| Category | Club Repair & Clubmaking Supplies |
For best results, ensure shaft tip and hosel bore are thoroughly cleaned and lightly abraded before applying adhesive. Allow the assembled club to rest undisturbed for the full cure period before taking it to the course.
Specifications
No additional properties are available for this product.
Rating
We'd love to hear your opinion
Your review will help us and other customers when buying this product.
Please log in to add a review.
No reviews for this product yet.
Questions
